Just How to Install a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Just How to Install a Bathtub: Set Up an Acrylic Bathtub and Bathtub Surround
Blog Article
Just how do you actually feel on the subject of How to Install a Bathtub?
Setting up a bathtub isn't specifically rocket science, yet it does need solid plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a reasonably challenging job. If the old tub is readily accessible, the project can relocate immediately; if you need to open a wall to remove the old bathtub and also place the new bathtub, the task is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub as well as set in the new one. Make sure you have actually qualified yourself for the work and also fit attempting it. Rather than working with a specialist to take over a halfway-completed task, it is far better to think about employing one prior to you start. Chances are you might require an expert plumber to make tube connections.
This write-up will help you mount a brand-new bathtub in your washroom if you have already gotten a brand-new tub and also do not need to transform the plan of your previous water pipelines.
Your tools and also material checklist must comprise the following:
Preparing for the Installment
First of all, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its final setting.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The process of removing the existing taps can be rather bothersome due to the restricted access that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Before moving on to fit the new taps, compare the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are handy in equally spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the furthest adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water supply and examine all joints and also brand-new pipework for leakages as well as tighten them if necessary. Load the tub and also examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has been used at the very least once as this will settle it right into its last position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location in between the tap and also the sink. Protect the faucet in position with the producer given backnut. When the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The former type must be attached to the tap finishes first, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split an inflexible seal, causing the water to permeate the wall surface between the bath and also the tiling, leading to problems with moisture and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to constantly load the bathtub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split fairly early if you do not take into consideration this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very involved in How to Install a Bathtub Yourself and I really hope you appreciated the entire blog entry. For those who appreciated our page plz do not forget to share it. Thank you for your time invested reading it.
Get Your Estimate Now
Report this page